Post Wiki

This page is read only. You can view the source, but not change it. Ask your administrator if you think this is wrong.
===== Drilling Custom Parameters =====

Image showing all drilling custom parameters:

{{ :mp:drilling_custom_parameters.jpg?nolink&600 |}}

XML text section of custom parameters at bottom of post. drl_param variable sections are near bottom:
<code xml>
		<simple_drill>
			<description>
				<text>Drill/Counterbore - G81</text>
			</description>
			<feed_rate>
				<text>""</text>
			</feed_rate>
			<dwell>
				<text>Dwell - P</text>
			</dwell>
			<first_peck>
				<text>""</text>
			</first_peck>
			<subsequent_peck>
				<text>""</text>
			</subsequent_peck>
			<peck_clearance>
				<text>""</text>
			</peck_clearance>
			<retract_amount>
				<text>""</text>
			</retract_amount>
			<shift>
				<text>""</text>
			</shift>
		</simple_drill>
		<peck_drill>
			<description>
				<text>Peck Drill - G83</text>
			</description>
			<feed_rate>
				<text>""</text>
			</feed_rate>
			<dwell>
				<text>Dwell - P</text>
			</dwell>
			<first_peck>
				<text>Peck - Q</text>
			</first_peck>
			<subsequent_peck>
				<text>""</text>
			</subsequent_peck>
			<peck_clearance>
				<text>""</text>
			</peck_clearance>
			<retract_amount>
				<text>""</text>
			</retract_amount>
			<shift>
				<text>""</text>
			</shift>
		</peck_drill>
		<chip_break>
			<description>
				<text>Peck Drill - G73</text>
			</description>
			<feed_rate>
				<text>""</text>
			</feed_rate>
			<dwell>
				<text>Dwell - P</text>
			</dwell>
			<first_peck>
				<text>Peck - Q</text>
			</first_peck>
			<subsequent_peck>
				<text>""</text>
			</subsequent_peck>
			<peck_clearance>
				<text>""</text>
			</peck_clearance>
			<retract_amount>
				<text>""</text>
			</retract_amount>
			<shift>
				<text>""</text>
			</shift>
		</chip_break>
		<tap>
			<description>
				<text>Rigid Tap - G884</text>
			</description>
			<feed_rate>
				<text>""</text>
			</feed_rate>
			<dwell>
				<text>Dwell - P</text>
			</dwell>
			<first_peck>
				<text>""</text>
			</first_peck>
			<subsequent_peck>
				<text>""</text>
			</subsequent_peck>
			<peck_clearance>
				<text>""</text>
			</peck_clearance>
			<retract_amount>
				<text>""</text>
			</retract_amount>
			<shift>
				<text>""</text>
			</shift>
		</tap>
		<bore1>
			<first_peck>
				<text>""</text>
			</first_peck>
			<subsequent_peck>
				<text>""</text>
			</subsequent_peck>
			<peck_clearance>
				<text>""</text>
			</peck_clearance>
			<retract_amount>
				<text>""</text>
			</retract_amount>
			<shift>
				<text>""</text>
			</shift>
		</bore1>
		<bore2>
			<first_peck>
				<text>""</text>
			</first_peck>
			<subsequent_peck>
				<text>""</text>
			</subsequent_peck>
			<peck_clearance>
				<text>""</text>
			</peck_clearance>
			<retract_amount>
				<text>""</text>
			</retract_amount>
			<shift>
				<text>""</text>
			</shift>
		</bore2>
		<misc1>
			<first_peck>
				<text>""</text>
			</first_peck>
			<subsequent_peck>
				<text>""</text>
			</subsequent_peck>
			<peck_clearance>
				<text>""</text>
			</peck_clearance>
			<retract_amount>
				<text>""</text>
			</retract_amount>
		</misc1>
		<misc2>
			<description>
				<text>G84/G74 - Tap no Peck</text>
			</description>
			<dwell>
				<text>""</text>
			</dwell>
			<first_peck>
				<text>""</text>
			</first_peck>
			<subsequent_peck>
				<text>""</text>
			</subsequent_peck>
			<peck_clearance>
				<text>""</text>
			</peck_clearance>
			<retract_amount>
				<text>""</text>
			</retract_amount>
			<shift>
				<text>""</text>
			</shift>
		</misc2>
		<drill_cycle_9>
			<description>
				<text>Multi depth/feed</text>
			</description>
			<dwell>
				<text>""</text>
			</dwell>
			<first_peck>
				<text>""</text>
			</first_peck>
			<subsequent_peck>
				<text>""</text>
			</subsequent_peck>
			<peck_clearance>
				<text>""</text>
			</peck_clearance>
			<retract_amount>
				<text>""</text>
			</retract_amount>
			<shift>
				<text>""</text>
			</shift>
		</drill_cycle_9>
		<simple_drill_custom_parameters>
			<description>
				<text>LABEL OF THE ENTIRE CUSTOM PAGE</text>
			</description>
			<parameter_1>
				<text>TEXT LABEL FOR 1ST CUSTOM PARAM</text>
                                <inch_value>1.</inch_value>
                                <metric_value>1.</metric_value>
			</parameter_1>
		</simple_drill_custom_parameters>
		<peck_drill_custom_parameters>
			<description>
				<text>Custom Drill Parameters 2</text>
			</description>
		</peck_drill_custom_parameters>
		<chip_break_drill_custom_parameters>
			<description>
				<text>Custom Drill Parameters 3</text>
			</description>
		</chip_break_drill_custom_parameters>
		<tap_custom_parameters>
			<description>
				<text>Custom Drill Parameters 4</text>
			</description>
		</tap_custom_parameters>
		<bore1_custom_parameters>
			<description>
				<text>Custom Drill Parameters 5</text>
			</description>
		</bore1_custom_parameters>
		<bore2_custom_parameters>
			<description>
				<text>Custom Drill Parameters 6</text>
			</description>
		</bore2_custom_parameters>
		<misc1_custom_parameters>
			<description>
				<text>Custom Drill Parameters 7</text>
			</description>
		</misc1_custom_parameters>
		<misc2_custom_parameters>
			<description>
				<text>Custom Drill Parameters 8</text>
			</description>
		</misc2_custom_parameters>
		<drill_cycle_9_custom_parameters>
			<description>
				<text>Custom Drill Parameters 9</text>
			</description>
		</drill_cycle_9_custom_parameters>
		<drill_cycle_10_custom_parameters>
			<description>
				<text>Custom Drill Parameters 10</text>
			</description>
		</drill_cycle_10_custom_parameters>
		<drill_cycle_11_custom_parameters>
			<description>
				<text>Custom Drill Parameters 11</text>
			</description>
		</drill_cycle_11_custom_parameters>
		<drill_cycle_12_custom_parameters>
			<description>
				<text>Custom Drill Parameters 12</text>
			</description>
		</drill_cycle_12_custom_parameters>
		<drill_cycle_13_custom_parameters>
			<description>
				<text>Custom Drill Parameters 13</text>
			</description>
		</drill_cycle_13_custom_parameters>
		<drill_cycle_14_custom_parameters>
			<description>
				<text>Custom Drill Parameters 14</text>
			</description>
		</drill_cycle_14_custom_parameters>
		<drill_cycle_15_custom_parameters>
			<description>
				<text>Custom Drill Parameters 15</text>
			</description>
		</drill_cycle_15_custom_parameters>
		<drill_cycle_16_custom_parameters>
			<description>
				<text>Custom Drill Parameters 16</text>
			</description>
		</drill_cycle_16_custom_parameters>
		<drill_cycle_17_custom_parameters>
			<description>
				<text>Custom Drill Parameters 17</text>
			</description>
		</drill_cycle_17_custom_parameters>
		<drill_cycle_18_custom_parameters>
			<description>
				<text>Custom Drill Parameters 18</text>
			</description>
		</drill_cycle_18_custom_parameters>
		<drill_cycle_19_custom_parameters>
			<description>
				<text>Custom Drill Parameters 19</text>
			</description>
		</drill_cycle_19_custom_parameters>
		<drill_cycle_20_custom_parameters>
			<description>
				<text>Custom Drill Parameters 20</text>
			</description>
		</drill_cycle_20_custom_parameters>
</code>
Post Wiki

User Tools

Site Tools

Page Tools
